News and Announcements

Interested in learning about blacksmithing? Read this!

--News & Announcements--
Upcoming projects:
Building a Frame Saw
Forging a Copper Kettle
Making a pair of leather work boots
Forging and Fletching a Bodkin
Flocking a drawer interior

Tuesday, July 30, 2013

Simple Bowstring

If you are like me, then you have bows but no strings. If you are also like me, then you have had bows without strings for several months. As this is generally useless, I decided to finally get around to making a few strings for them. There are a few different ways this can be done, so I decided to ignore all of them and invent my own. In the following post, I will be making a simple bowstring with a Flemish loop at each end.

The first step is to take a bow or the dimensions for a bow and determine how many strands and how long the string needs to be. I have no experience with this, so I found it online. The number of strands will likely vary with what string material you are using. I have B-50 string material, and for the bow in question (~35-40#) I will be using 14 strands, seven each of red and black. Only one colour is necessary, but it is easier to see what I am doing with two. With that done, I took the length of my bow and added 10 or so inches to accommodate the loops and shrinkage due to twisting it.


To hold everything in place, I took two C clamps and fastened them to the edge of a table with the screw end up. I tied one end to the screw and made seven passes with each colour, for a total of 14 strands. 


Keeping the two halves separate, I cut off the loops from one end and made the end tapered. To do that, I simply cut the seven strands at an angle so it faded more gradually. This is not critical, but will make it easier to handle later. Do the same thing with the other 7 strands. 


Now, I took each bundle and twisted it slightly to the counter clockwise direction. This was merely to keep it from falling all over the place and tangling with itself. I went that direction because it will unwind with the twisting of the Flemish loops leaving a nice neat and straight bundle later.


With both halves twisted enough to keep them together, take them and pinch them together around where the shortest end stops (end of the fade). You do NOT want to have the faded part of string inside the loop, as it will weaken the entire string. The loop is probably the first place a string will break unless it is not served where the arrow nocks. The reason for this is it contacts the bow and experiences a different distribution of stress than the rest of the string, and thinning it asks for it to be broken. (ask me how I know)

NOTE: from here out, you can do this with either orientation, but if you do it the other way, you will need to do everything opposite what I am doing.


Both bundles in your left hand, with the tapered ends off to the left (you are working to the right), take the topmost and  twist it with your right hand  by rolling it between thumb and fingers. Twist it away from you so it looks like mine. The direction of twist here is important, for if you do it the wrong way, the Flemish twist will not work. It will be quite obvious if you do it wrong, as the thing will not stay together.


Holding the twist in the string with your fingers, bring the top strand down over the bottom so it crosses in front as you see it.

Careful to keep the first bundle from untwisting, take the second (black, now on the top) and do the same thing. Twist out and away from you and bring it down over the first (red). If you are curious about what is going on here, take any piece of string and twist it a lot. That is, until it starts to buckle and form a corkscrew shape. That is essentially what is happening here, except we have two of the screws and are interlacing them. The twist from your fingers brings the string to fit against the other, and working them progressively keeps it from creating ripples and errors that compromise the string.


Continue to do the same thing, twisting the top string and bringing it down over the bottom, until it begins to look like this. Depending on how tight you want the turns, you can pull the top bundle farther over the bottom or leave it farther out away from the anchored end. I tied a string around the free end to keep it from being worked loose, but it will stay together naturally. After all, that is the whole point of the Flemish twist. If you have any question as to how much to twist the bundles between your fingers, it is better to have more than less. Releasing the strands will allow them to untwist a little, so a heavier twist later will help reset what is already inside the Flemish part (two wrapped together).


Depending on how thick your bow is will determine the next step. To form the actual loop, you need only as much Flemishly twisted string as will fit around the nock of your bow. Mine was about 6cm long at this stage. Fold the newly twisted string in half as shown so the two untwisted ends align.


This is where having two colours makes it easier. Take the two red ones and pull them together, then the same with the black. This will leave the string with half of the ends on one side, half on the other. If this is confusing to describe, just look at the above picture.


Take the reds and work them together into a single bundle as shown, same with the black. Begin to do the same thing as you did in the start, twisting the top out and away and pulling it down over the bottom to the front. Rinse and repeat.


To determine how far down to go with the Flemish loop, I went about 3cm past the bottom of the fade. You will be able to see where the longest end was by where it sticks out from the twists. Those are nothing to worry about, as they can be cut off later.


You should now have a Flemish loop. I tied mine off with a bit of string to keep it nice and tidy while I do the second.


At this stage, you will need some indication of how long the string actually needs to be. A recommended to me approximation is the length of the unstrung bow from nock to nock, less 3 inches. I did not do this. Instead, I took a piece of synthetic rope I had been using until now as a string and simply measured it. I knew it was the proper length, so no harm there. Be wary of this, however. Some materials will stretch under tension, and for that method to work it must not. A strung bow should have the string approximately the length of your fist with thumb up from the handle to the string, more or less depending on your preference. Or, more accurately, the bowyer's preference. So, I took the fake string and used it to find the top of the second loop and tied it with a string.


Cut the strands same as before, tapering them nicely. I probably should have mentioned this before now, but bow string material is waxed. If it ever stops sticking together after a little effort, re wax it with something. (Beeswax? I have not yet encountered this issue).


I cut the bundles so that they were only long enough to make the loop with the fade into the rest of the string. Much longer, and it will be a mess to try and fix later. An estimate of this length can be found by laying it next to the first loop and trimming accordingly. At this stage, I moved the string up to the top of the fade (where the loop will intersect with itself) and did the same thing as with the first loop.

Note: the string will accumulate some twist to it, because the bundles cannot untwist freely due to the loop at the other end. If you did not notice this before, the strings will accumulate twist from rolling them between your fingers. Do not worry about it, as it will help keep the string together. For whatever reason, the twist from the second loop is in the same direction as that from the first instead of opposite. If this makes no sense to you, simply do not worry about any of it. Proceed with the loop as though there is nothing wrong (because there is not).


With the second section as long as the loop it will become, I folded it in half just as before. The loops are slightly larger than the bow at the nock, as it needs to slide down onto the body of the bow to be strung.


This picture represents a little more clearly what I meant about separating the two colours when joining the loop. Red to red and black to black, turning the four bundles into two, one of each colour. Now do the same thing to finish the loop.


Here are the two loops side by side, the first trimmed and nice. Both are the same size. But we are not  done yet!


See the internal twist? This is the product of the Flemish loops. Nifty.


Serving. That is the last step before you can finally go shooting. You will need serving (obviously) to do this. Also, not required but highly recommended, is a serving jig. I made mine in about five minutes from a piece of scrap. Or you can buy one onlie. I will make a post about that later. Here, I returned the string to the clamps to suspend it. There is enough tension to keep it from sagging, but it is not super taught. BEFORE starting to serve the string, cut a ~10cm piece of serving off and set it to the side. To start, thread the serving between the two bundles and bring it to the end of the Flemish twist. Tie a knot if you want to. Or don't. It does not matter much. Start for real by bringing the working end of the serving about 2cm in from the end of the twist. The idea here is twofold. One, to cover the ends of the taper if you did a bad job of cutting them off or chose not to altogether. Two, to cover the transition from twist to straight. Serving this part of the string is not essential, and many I have seen do not, but it took only a few minutes so why not?


Roll the spool of serving until the groove of the jig rests against the string as shown. Now just spin it around the string. Doing this by hand may leave gaps in the serving, but there is something magical about the jig that keeps it perfect. No smoke and mirrors here. I held the non-clamp end of the string to keep it from twisting, and just spun the jig around as fast as I reasonably could without it flying off. I recommend having your serving jig tightened around the spool (by that bolt that keeps it in the jig) enough that it will not unwind under its own weight but not so tight it takes more than a little effort to wind around the string. It is one of those things that is easier done than said. Experiment around for yourself until you find the sweet spot.


Finishing the serving must be taken into account before you are ready to end it. Take that ~10cm piece of serving and put one end along the string so the next wrap of the serving goes over it and holds it in place. Fit it into the small gap between bundles or don't, your choice. Now wind the serving around the three strands (red, black, and serving you just put in) for five or so turns.


Now take the other end of the 10cm string and fold it over to form a loop. Leave the loop large, but overhang the free end back towards the Flemish loop long enough to grab onto later. Wrap it up with everything else for another five to seven turns. Any more than that, and the waxed bowstring will have provide too much friction and the serving will snap.


By now, the middle of the serving you wound around the string should be about on the transition from Flemish twist to straight string. If not, as long as it is covered you are alright. Pull the serving jig down to unroll some thread.


Pinch the string at the end of the wound serving and cut the spool/jig free. Be careful not to let everything you have worked to do unravel.


Push the cut end through the loop you made earlier as shown, still keeping everything held in place between the fingers of your other hand. Pull the long end of the serving loop towards the Flemish loop until it comes tight against the end of the serving wrap. Now pull it a little farther so it is underneath the serving.


Cut it all free, and you are a third of the way done serving.


Nearly done. With both ends served, all that remains is to serve the nock. This is the most important area to protect, as the nock of the arrow will wear the string very quickly if left unprotected. Remember to cut your extra piece of serving!! For this, we need to actually string the bow. The reason being, we need to know where we need to serve. I mark the area with those handy pieces of string that were left on from before. The top (left side) is 7cm or so above where the arrow shaft will rest when drawn. The bottom (right side) is about the same distance below the bottom of the grip. You want to go that far down because the string wears equally as fast when slapping against an armguard. Also, if you string it upside down, you will not be shooting off of unprotected string.


Start by tying the serving to the string, same as before. Take it as slow as you need to. One thing that I would do at this point is even out the internal twisting of the string. If one half is almost straight and the other very twisty, push the twists to the barren area and even it out. This cannot be done easily after the centre is served. (There are ways around it, but it is not quite the same).


Finish with the same loop and pull method as before and trim the excess serving.


And now the string is served.


There you have it, one string ready for use. The total time took me about 40 minutes ,including taking the photos.  

Saturday, July 6, 2013

The World is Fake

The world is fake.

It is as simple as that, no beating around the fact. Over the course of the past hundred years or so, the world has begun to walk down a dangerous road. I would never argue the merits of technology, yet the state of affairs it has left us in is almost sickening. The first world mentality of making everything disposable, cheap and fast to produce has shifted our perspective far from the path of the Age when mankind took value in the nature of possession. Tools were meant to serve their purpose and to last beyond a single task. Homes were meant to be cherished as a place of sanctuary and comfort instead of a temporary step until the future brought about a better prospect. Food was made by the caring hands of people who could look out a window and say exactly where it came from. But so little of that remains now that, unless those few hold onto those ways, it will be lost forever.

The walls in front of me are cheap slabs of drywall covered in cheap plaster, painted with cheap paint and adorned with fibreboard framed prints and plastic decorations that no craftsman would ever be proud to say they created. The roof above me is shingled in synthetic cloth covered in crushed gravel and tar bought by the hundredweight. The food I ate came in a thin plastic shell adorned with bright colours and the small square filled with nutrition facts that would kill mice by the score. 1660mg of sodium in a mere 3 ounces. Acetylated Monoglycerides. Apocarotenal. Lactic Acid. Monosodium Glutamate. Ferrous Sulfate. The tag sewn crooked into my shorts reads 82% polyester. What is the other 18%? Maid in China. Not made? Hecho en México. Thailand. Korea. Assembled in Vietnam. I am grateful for the roof above my head, the food upon my plate, the clothing on my back, the opportunities afforded to me over the years I have already lived and the time that remains to be held. I am grateful, but I cannot look in a mirror without finding a bitter taste of disgust.

"This summer I saw King Tut's tomb."
"You visited Egypt?"
"No, I saw a replica in the Egypt section of Busch Gardens." 
Gaudy colours and plaster covered chicken wire. Shops playing popular music out of the speakers above their doors, enticing tourists to their wares. There on the wall in the waiting queue hangs a collection of faux tribal sticks and torches bound together with cloth. No, that is just mesh where the paint has chipped away. There above the entrance are a collection of metal lanterns with heavy bolts holding them against the afternoon storms. No, they are plastic, the injection-moulded seams so obvious that whoever pulled them off the assembly line checked to see if they were in one piece and left it at that. This is supposed to be entertainment, and it is just a lie. Fake. Shallow and depressing. The world is melding together, the only culture people know rising from the silver screens and amusement parks. So many people will live content with deception. So many people will never appreciate the living bridges of Cherrapunji, woven for generations beyond the eyes of western civilization. So many people will never experience the massive subterranean world of Son Doong, or South Africa's Victoria Falls, or the Stave Churches of Norway. We are living in a dream that, when we wake, the only comfort that remains will be our memory. Sadly, it seems that if it is not presented on a backlit display, no one longer seems to care.

"Is that a park?"
"No, that is the past thirty years of human history." 
They say that the largest elevation change on Long Island is its landfill.

Seeing the traditional Finnish carpenters build a house with an axe and an adze from nothing but trees and rocks, it makes me wonder how long the asbestos insulated 'American Dream' will last. We have churches that celebrate their millennia anniversary, but what will be left of our Age a thousand years from now? Ruins of the glory days. Rusted metal and broken glass and trash heaps that climb the mountainsides. Why? Because that is what our mentality has become. Use and forget. It does not need to last a lifetime, only long enough to do the job. Why? Because there will be something better if I ever need it again. Why invest when the technology will be outdated? But hammers have not been reinvented in the last year. Nor have the shirts I wear. Or the shoes on my feet or the frame of my bicycle.

I saw an armguard the other day, the sort used for archers to protect their wrists. Black plastic with elastic cords to hold it on. Did it serve its purpose? For the time being, it would. $5 is a small price to pay. It is forgettable, liquid. And so is the object it procures. Why buy what you can make? And so I decided to make my own. Brass and leather, no painted plastics or synthetic fibres pressed into a sheet. I decided to make my own because I know it will last. I know that I value my own workmanship, and that if I am willing to put the time into producing it that I too am willing to see it done properly. If I take the time to create this object, I know I will not be throwing it away or replacing it when they invent new bulletproof armguards that you cannot cut and can be hit with a train, because I do not need that. Nor, it could be argued, do I need an armguard at all, same as I do not need a bow or the arrows to shoot out of it. I do not need the tools I use or computer upon which I write. I do not need a car, I do not need shoes. But it is not my aim to reduce human life to its simplest form. I do not wish to take it all away; rather, I seek to take these hands that have been so graciously given to me to create things that replace the artificial nature that humanity has tended towards. Why is it that we can still find thousand year old artefacts, yet a thousand years from now all they will find is a heap of refuse? Because we chose to make it that way.

A lantern, a knife, a bow, a map- if I can make it, I will. If I can make it, if I can understand the process and gain the skill, I will hold no illusions as to its composition. I know that this ink will not be washed away with yesterday's rain, I know that this wood is not particle board. I know that I can trust this steel to cut without breaking and to hold an edge beyond what the commercial knife would claim. I know that this bread will not work against my body.

In a turn of the century farmer's barn where scythes and pitchforks were not hung on the wall to decorations, in an old time blacksmith's shop where the timbers are painted black with the dust of coal, in the basement of a house with a stone foundation, in the middle of a field where the only thing around is nature itself, the simplest things make all the difference. Forging with a hand made hammer upon steel smelted from nothing but ore, carving with a hand made knife, shooting with a hand made bow, lighting the room with a hand made lantern, there is something about the nature of hand crafted objects that can never be replicated. What you surround yourself with is what others use to identify you, to measure you. In a sense, they are what you become.

I want to be inspired by the tools I use, to feel the sweat of labour that went into creating them. I want to be driven by the passion of that craftsman as I use their legacy to create my own work. I want the walls around me to spark my imagination and thoughts of places of the distant worlds once so well versed in the arts I try to reproduce. I want not to sit in a room and feel like it is instead a prison. I want to love working where I work and want to come back to that place every day for the rest of my life. I want to be inspired by my dinner plate and the table beneath it. By the fire that cooks my meal and the hearth that contains it. The pots and the pans and my door catch and the hinges. It may seem foolish, it may seem naïve, but it does not need to be that way. It does not, and yet for so many it is.

Only premium quality. Genuine. Precision. The finest. Luxury. What do these words mean to you?